We have unearthed this great article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the web and felt it made sense to share it with you here.
Mounting a tub isn't precisely rocket science, yet it does need strong plumbing, carpentry, and often, tiling skills. Replacing an old tub with a new one is additionally a moderately difficult job. If the old bathtub is conveniently available, the task can move speedily; if you need to open a wall to get rid of the old bathtub as well as position the brand-new bathtub, the task is a lot harder. In either situation, the job is within a home handyman's skills, although you will require a helper to move out the old tub and also set in the new one. Make certain you have actually certified on your own for the job and also fit trying it. Instead of working with a service provider to take control of a halfway-completed task, it is much better to consider using one before you begin. Opportunities are you might require a professional plumber to make tube links.
This post will assist you mount a brand-new bathtub in your shower room if you have actually currently gotten a brand-new tub and do not need to change the setup of your previous water system pipelines.
Your tools as well as material checklist ought to comprise the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The process of removing the existing taps can be fairly troublesome due to the restricted gain access to that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this process. Once the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing compound.
Prior to carrying on to fit the new taps, compare the pipe links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the tap as well as the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washers are in place in between the tap and also the sink. Protect the faucet in place with the producer offered backnut. When the tap is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former kind needs to be linked to the tap finishes first, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Utilizing both wooden boards under its feet, place the bathtub in the needed placement. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by checking the level as well as changing the feet on the bathtub till the spirit level reviews degree.
To set up taps, fit all-time low of the furthest adaptable tap connector to the suitable supply pipeline by making a compression join; then do the very same for the other faucet.
Activate the water supply and also check all joints as well as new pipework for leakages as well as tighten them if needed. Load the tub as well as likewise check the overflow electrical outlet and the regular outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the producer's user's manual. Tiling and sealing around the bathtub ought to wait up until the tub has been utilized a minimum of once as this will settle it into its final position.
Planning for the Installation
To start with, the supporting structure provided with the bath needs to be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make sure that if the faucet includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets unit to prevent stress on the tub.
Fit the flexible faucet adapters to the bottom of the two faucets using 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to split a stiff seal, creating the water to permeate the wall in between the bathroom as well as the tiling, leading to complications with moisture and also possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes as well as cartridges, and are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split relatively very early if you do not think about this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently readily available on the market. It is recommended to fit the floor tiles using water-resistant or water resistant sticky and cement.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
Do you enjoy reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave feedback down the page. We would be glad to listen to your insights about this page. We hope that you visit us again in the future. Are you aware of another individual who is excited about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Be sure promote it. I appreciate reading our article about How to Install a Bathtub Yourself.
Schedule Here